Breathe3D Mask Care Instructions

Breathe3D Mask Care



THE BREATHE3D MASK CONTAINS:

A.  1 - Breathe3D Mask
B.  2 - Elastic Ear Loops
C.  1 - Foam Seal
D.  1 - 2.5” x 2.5” MERV-13 Filter
E.  1 - Essential3D Ear Saver

 

BREATHE3D MASK DAILY USE:

  1. Wash hands before using mask.
  2. Place ear saver between the ear loops.
  3. Place mask over nose & mouth
  4. Slide ear saver in the ear loops over the top of your head, resting the ear saver on the back of your head
  5. Ensure the mask has a solid seal around the bridge of your nose and over the tip of your chin.
  6. Wash hands after placing the mask on your face.
  7. Masks are reusable and should be cleaned daily.
  8. Do Not Share Masks!
  9. Do Not Leave Masks In A Hot Car
  10. Do Not Hang Masks On Rear View Mirrors

 

CLEANING BREATHE3D MASK:

  1. Clean mask with soap and water or alcohol wipes. 
  2. Do not clean the mask in a dishwasher.
  3. Wash hands before and after masking up, changing filters and removing mask.

CLEANING THE MERV-13 Filter

  1. Use soap & water to gently clean MERV-13 Filter. 
  2. Rinse MERV-13 with cool water.
  3. Air Dry MERV-13 Filter Overnight
  4. Filter can be washed 8-10 times before replacing 


REPLACING THE BREATHE3D FILTER

  1. MERV-13: Order replacement by clicking here or visiting: https://store.designedbyus.org/collections/essential-protection/products/breathe3d-filters-10-pack
  2. Single Use Medical Mask Filter: Replace filter by cutting single use medical mask in to 4-6 2.5 x 2.5 filters.
  3. 100% Cotton Filter: Replace filter by cutting 100% cotton into 2.5”x 2.5” squares.
  4. Eucalyptus Lycolell: Replace filter by cutting Eucalyptus Lycolell into 2.5”x 2.5” squares.

Custom Fit Your Mask: We print these masks to fit a wide variety of facial sizes, but we know everyone’s face is different. To adjust the fit of the mask, it can be gently heated with a hair dryer or steam to make the material more malleable. Once it has been softened, simply mold the mask to your liking and allow the mask to cool completely before using.

Daily Cleaning: Masks should be cleaned after each use with soap and water and allowed to air dry before reuse.

 

REPLACING THE BREATHE3D FOAM SEAL

    1. Using Silicone Rubber, Ethylene propylene diene terpolymer foam or Self Adhesive Foam Weatherstrip use the following measures for your size of mask: 
      1. Small - 13.75 Inches
      2. Medium - 14 Inches
      3. Large - 14.5 Inches
      4. Extra Large - 14.75 Inches
      5. 2XL - 17 Inches
    2. Remove Adhesive backing and replace foam.

 

BREATHE3D MASK DIAGRAM

 

How To Use Breathe3D Mask with an Essential3D Ear Saver 

 

USO DIARIO DE LA MÁSCARA BREATHE3D:

  1. Lávese las manos antes de usar la mascarilla.
  2. Coloque el protector de orejas entre las presillas.
  3. Coloque la mascarilla sobre la nariz y la boca
  4. Deslice el protector de orejas en las presillas sobre la parte superior de la cabeza, descansando el protector de orejas en la parte posterior de la cabeza.
  5. Asegúrese de que la máscara tenga un sello sólido alrededor del puente de la nariz y sobre la punta de la barbilla.
  6. Lávese las manos después de colocarse la mascarilla en la cara.
  7. Las máscaras son reutilizables y deben limpiarse a diario.
  8. ¡No comparta máscaras!
  9. No deje máscaras en un automóvil caliente
  10. No cuelgue máscaras en los espejos retrovisores

MASCARILLA LIMPIADORA BREATHE3D:

  1. Limpiar la mascarilla con agua y jabón o toallitas con alcohol.
  2. No limpie la mascarilla en el lavavajillas.
  3. Lávese las manos antes y después de enmascarar, cambiar filtros y quitarse la mascarilla.

LIMPIEZA DEL FILTRO MERV-13

  1. Use agua y jabón para limpiar suavemente el filtro MERV-13.
  2. Enjuague MERV-13 con agua fría.
  3. Filtro de secado al aire MERV-13 durante la noche El filtro se puede lavar de 8 a 10 veces antes de reemplazarlo